Good links
East Coast Gear Supply - complete assembled 3rds
www.brian894x4.com (axle codes)
Breaking in gears and other useful documents
Cruiser Outfitters turns Fj60 axle housings
ToyoDIY.com (part number database and more)
My cheatsheet(outdated)
4Runner History(1st gen thru 6th)
Information for new '91-'97 Toyota Land Cruiser 80 series owner
Toyota bearing numbers
*********************************************************************************************************************************
*********************************************************************************************************************************
79~85 (REAR) mini-truck models
(45mm journals)
outer pinion
KOYO 30306JA cone/30306J-N cup verified (90366-30008-77 $48.11 retail)
inner pinion
KOYO 32307JR cone/32307J cup verified
NACHI E32307JN same
TIMKEN X32307 cone/Y32307 cup
carrier
TIMKEN LM603049 cone/LM603014 cup verified
NACHI 17887
TIMKEN 17887
NSK 17887 cone/17831 cup verified
The very common 8" pinion shim sizes/part numbers....
90564-35109 T=1.70 .0669" $3.52
90564-35110 T=1.73 .0681" $3.52
90564-35111 T=1.76 .0693" $3.52
90564-35112 T=1.79 .0705" $10.64
90564-35113 T=1.82 .0717" $3.52
90564-35114 T=1.85 .0728" $3.52
90564-35115 T=1.88 .0740" $3.52
90564-35116 T=1.91 .0752" $3.52
90564-35117 T=1.94 .0764" $3.52
90564-35118 T=1.97 .0776" $3.52
90564-35119 T=2.00 .0787" $3.52
90564-35120 T=2.03 .0799" $3.52
90564-35121 T=2.06 .0811" $3.52
90564-35123 T=2.09 .0823" $3.52
90564-35124 T=2.12 .0835" $3.52
90564-35125 T=2.15 .0846" $3.52
90564-35126 T=2.18 .0858" $3.52
90564-35127 T=2.21 .0870" $3.52
90564-35128 T=2.24 .0882" $3.52
90564-35129 T=2.27 .0894" $3.52
90564-35130 T=2.30 .0906" $3.52
90564-35131 T=2.33 .0917"
Solid collar final length~~2.440"..... observed 2.434" (2.374 + .060)
*********************************************************************************************************************************
*********************************************************************************************************************************
86~95 (REAR) 22R/22RE models
(45mm journals)
outer pinion
KOYO TRA0607RYR-N cone/TRA0607-N cup (genuine Toyota part # 90366-30022-77 $48.72 retail)
NACHI TRA0607RYR-N cone/TRA0607-N cup
inner pinion
KOYO TR070803C-N (cone/cup # is same,"N" is optional) verified...genuine Toy superceded part is 90366-35044-77 $63.84 retail
NACHI 35KC802 (cone/cup # same)
carrier
TIMKEN LM603049 cone/LM603014 cup verified
NACHI 17887 same verified
TIMKEN 17887 same
NSK 17887 same
The very common 8" pinion shim sizes/part numbers....
90564-35109 T=1.70 .0669" $3.52
90564-35110 T=1.73 .0681" $3.52
90564-35111 T=1.76 .0693" $3.52
90564-35112 T=1.79 .0705" $10.64
90564-35113 T=1.82 .0717" $3.52
90564-35114 T=1.85 .0728" $3.52
90564-35115 T=1.88 .0740" $3.52
90564-35116 T=1.91 .0752" $3.52
90564-35117 T=1.94 .0764" $3.52
90564-35118 T=1.97 .0776" $3.52
90564-35119 T=2.00 .0787" $3.52
90564-35120 T=2.03 .0799" $3.52
90564-35121 T=2.06 .0811" $3.52
90564-35123 T=2.09 .0823" $3.52
90564-35124 T=2.12 .0835" $3.52
90564-35125 T=2.15 .0846" $3.52
90564-35126 T=2.18 .0858" $3.52
90564-35127 T=2.21 .0870" $3.52
90564-35128 T=2.24 .0882" $3.52
90564-35129 T=2.27 .0894" $3.52
90564-35130 T=2.30 .0906" $3.52
90564-35131 T=2.33 .0917"
Solid collar final length~~2.389
*********************************************************************************************************************************
*********************************************************************************************************************************
88~95ish (REAR) 8" V6 models
(50mm journals)
outer pinion
KOYO STA3072 verified Toyota part # 90366-30025 superceded by 9036630067 ($49.93 retail)
next time order 9036630078
KOYO TR0607J-1 same verified
NSK R30-13
inner pinion
Toyota part # 90366-35028 superceded by 90366-35028-77 ($87.55 retail)
KOYO TR070904-1-N same (90366-35087 $91.40)verified
carrier bearing
KOYO TR100802-1-N cone/TR100802-2-N cup verified....90366-50007(retail $48.61)
JLM104948 cone/LM104912 cup .....NOT an acceptable substitute
(the OD of the LM104912 cup is .0027" smaller than the recommended genuine KOYO TR100802-2-N)
Using the 104912 could result in 'spun damage' to the bearing cap.
V6 4 pinion cases...sidegear thrust washer part numbers(updated/verified)
superceded part numbers below(4-21-13)
PART NUMBER mm inches retail
41361-60E00 0.875 .0344 $6.60
41361-60E10 0.900 .0354 $6.60
41361-60E20 0.925 .0364 $6.60
41361-60E30 0.950 .0374 $6.60
41361-60E40 0.975 .0384 $6.60
41361-60E50 1.000 .0394 $6.60
41361-60E60 1.025 .0404 $6.60
41361-60E70 1.050 .0413 $6.60
41361-60E80 1.075 .0423 $6.76
41361-60E90 1.100 .0433 $6.92
41361-60F00 1.125 .0443 $7.00
41361-60F10 1.150 .0453 $7.20
41361-60F20 1.175 .0463 $7.31
41361-60F30 1.200 .0472 $7.43
41361-60F40 1.225 .0482 $7.71
41361-60F50 1.250 .0492 $7.83
41361-60F60 1.275 .0502 $8.03
41361-60F70 1.300 .0512 $8.22
41361-60F80 1.325 .0522 $8.38
The very common 8" pinion shim sizes/part numbers....
90564-35109 T=1.70 .0669" $3.52
90564-35110 T=1.73 .0681" $3.52
90564-35111 T=1.76 .0693" $3.52
90564-35112 T=1.79 .0705" $10.64
90564-35113 T=1.82 .0717" $3.52
90564-35114 T=1.85 .0728" $3.52
90564-35115 T=1.88 .0740" $3.52
90564-35116 T=1.91 .0752" $3.52
90564-35117 T=1.94 .0764" $3.52
90564-35118 T=1.97 .0776" $3.52
90564-35119 T=2.00 .0787" $3.52
90564-35120 T=2.03 .0799" $3.52
90564-35121 T=2.06 .0811" $3.52
90564-35123 T=2.09 .0823" $3.52
90564-35124 T=2.12 .0835" $3.52
90564-35125 T=2.15 .0846" $3.52
90564-35126 T=2.18 .0858" $3.52
90564-35127 T=2.21 .0870" $3.52
90564-35128 T=2.24 .0882" $3.52
90564-35129 T=2.27 .0894" $3.52
90564-35130 T=2.30 .0906" $3.52
90564-35131 T=2.33 .0917"
Solid collar final length~~1.866"~1.868"
Freeze plug 3/4"..... Dorman 555-012 .69 each O'reilly Auto Parts (for blocking off ABS port)
*********************************************************************************************************************************
*********************************************************************************************************************************
*********************************************************************************************************************************
*********************************************************************************************************************************
2016+ (3rd Gen Tacos Sport non-TRD) REAR 8"
(53mm factory journals)
outer pinion
90366-T0083 ok to use 90366-30067 ........same as the older 8" V6 OPB
inner pinion
90366-T0080 ok to use 90366-35087 ........same as the older 8" V6 OPB
carrier bearing(2)
90366-T0010 ST5383/ST5383 is the factory replacement when re-using the factory center carrier(53mm journals)
90366-53004 will also work
90366-50007......a skinny 50/83mm bearing for aftermarket LSD's/Lockers that have 50mm journals. Same carrier bearing is used in the earlier model 8" diffs (TR100802-1-N cone/TR100802-2-N cup)
Pinion seal -- 90311-T0068 XH1701F recess 1mm (alternate can be 90311-41015 XH1701H)
71 for ring gear bolts (11mm flange style)
carrier bearing bolts use the usual 75 ft/lb
pinion flange bolt pattern 66x66
The very common 8" pinion shim sizes/part numbers....
90564-35109 T=1.70 .0669" $3.52
90564-35110 T=1.73 .0681" $3.52
90564-35111 T=1.76 .0693" $3.52
90564-35112 T=1.79 .0705" $10.64
90564-35113 T=1.82 .0717" $3.52
90564-35114 T=1.85 .0728" $3.52
90564-35115 T=1.88 .0740" $3.52
90564-35116 T=1.91 .0752" $3.52
90564-35117 T=1.94 .0764" $3.52
90564-35118 T=1.97 .0776" $3.52
90564-35119 T=2.00 .0787" $3.52
90564-35120 T=2.03 .0799" $3.52
90564-35121 T=2.06 .0811" $3.52
90564-35123 T=2.09 .0823" $3.52
90564-35124 T=2.12 .0835" $3.52
90564-35125 T=2.15 .0846" $3.52
90564-35126 T=2.18 .0858" $3.52
90564-35127 T=2.21 .0870" $3.52
90564-35128 T=2.24 .0882" $3.52
90564-35129 T=2.27 .0894" $3.52
90564-35130 T=2.30 .0906" $3.52
90564-35131 T=2.33 .0917"
Solid collar final length~~1.866"~1.868"
*********************************************************************************************************************************
*********************************************************************************************************************************
*********************************************************************************************************************************
*********************************************************************************************************************************
IFS 7.5" (FRONT) 86~95 models
Vehicle Application:(45mm journals)
1986-1989 Toyota 4Runner & Surf (4cyl)
1986-1988 Toyota Hilux Pickup (4cyl)
\
Vehicle Application:(50mm journals)
1986 Toyota 4Runner & Surf w/ 22R-TE
1986-1988 Toyota Hilux Pickup w/ 22R-TE
1988-1995 Toyota Hilux Pickup w/ 3.0 V6 3VZ-E
1988-1995 Toyota Runner & Surf w/ 3.0 V6 3VZ-E
1990-1995 Toyota Runner & Surf w/ 2.4 2L-TE Turbo Diesel, 3.0 1KZ-T, 3.0 1KZ-TE
1996-2002 Toyota 4Runner & Surf w/ 2.7 4 cyl 3RZ-FE, 3.4 V6 5VZ-FE, 3.0 1KZ-TE Turbo Diesel
1996-2002 Toyota Prado 90 w/ 2.7 4 cyl 3RZ-FE, 3.4 V6 5VZ-FE, 3.0 1KZ-TE Turbo Diesel
1995-2004 Toyota Tacoma w/ 2.7 4 cyl 3RZ-FE, 3.4 V6 5VZ-FE
1997-2004 Toyota Hilux Pickup w/ 2.7 4 cyl 3RZ-FE, 3.0 D4D Diesel
2000-2006 Toyota Tundra w/ 3.4 V6 5VZ-FE, 4.0V6 1GR-FE, & 4.7 V8 2UZ-FE
Does your passenger side inner CV axle stub seem too loose or wobbly(T100 owners need to read this)?
Outer pinion bearing
OEM part number = 90366-30078-77
KOYO TRA0607Rr-N cone/TRA0607-N cup verified
KOYO 30306JRYA-N cone/30306J-N cup verified
KOYO TR0607RYR-N cone/TRA0607-N cup verified
NSK HR30306J cup and cone verified
Inner pinion bearing
OEM part number = 90366-35023-77
KOYO TR0708-1r-N cone/TR0708-1-N cup verified
KOYO 32307 cone/32307J-N cup verified
KOYO TR0708-1YR-N cone/TR0708-1-N cup verified
NTN 4T 32307C cone and cup verified
Nachi 35KC802 cup and cone verified
"4 cyl" carrier bearing ....Toyota Part # 90368-45002 (45mm journals)
Nachi 17887 cone/ 17831S cup (correct offset for 4 cylinder)verified
Nachi 17887 cone/ 17831 cup (Cage interferes, don't ever use this bearing)
Timken LM603049 cone/LM603015 cup (add .022" shim behind both bearings 8-20-17)
Timken LM603049 cone/LM603014 cup (add .085" shim behind both bearings)
"V6" carrier bearing ....Toyota Part # 90368-50006 (50mm journal)
Nachi 50KB801LT cone/50KB801 cup correct offset verified
Koyo STB5080 correct offset verified
axle stub inner c-clip(2 desired) 90521-29002 retail $1.15
24mm pinion nut 90179-18001 retail $6.67 18mm thread dia
flanged pinion nut 90179-18020 ($2.18 retail) (18mm threads) verified
Solid collar final length~~2.170~2.197" 2.177" verified.... 2.196 also verified....best to reference old crush sleeve.
axle seal----IFS 7.5" front 3rd (2 needed for non-vacuum type) 90311-35032 $14.39 retail (86~95) verified also F1485 also "Yukon T1003"
Needle bearings---- 90364-33009 ....used on ADD fronts(because the stubs are spinning 100% of the time)
Non-ADD IFS fronts do not have needles...they have machined swirl marks. Axles only turn when the manual locking hubs are engaged.
The thicker 7.5" pinion shim part numbers/sizes....
90201-35434 .0882" MARK 01, T=2.24 1 $6.05
90201-35435 .0894" MARK 02, T=2.27 1 $6.05
90201-35436 .0906" MARK 03, T=1.76 1 $6.05
90201-35437 .0917" MARK 04, T=1.79 1 $6.05
90201-35396 .0929" MARK 05, T=2.36 1 $5.77
90201-35397 .0941" MARK 06, T=1.85 1 $5.77
90201-35398 .0953" MARK 07, T=2.42 1 $5.77
90201-35399 .0965" MARK 08, T=2.45 1 $5.77
90201-35400 .0976" MARK 09, T=2.48 1 $5.77
90201-35401 .0988" MARK 10, T=2.51 1 $5.77
90201-35402 .1000" MARK 11, T=2.54 1 $5.77
90201-35403 .1012" MARK 12, T=2.57 1 $5.77
90201-35404 .1024" MARK 13, T=2.60 1 $5.77
90201-35438 .1035" MARK 14, T=2.63 1 $5.77
90201-35439 .1047" MARK 15, T=2.66 1 $5.77
90201-35440 .1059" MARK 16, T=2.69 1 $5.77
90201-35441 .1071" MARK 17, T=2.72 1 $5.77
*********************************************************************************************************************************
*********************************************************************************************************************************
IFS 8" (FRONT hi-pinion) 98~07 Landcruiser fronts
Vehicle Application:
Front Diff
1985-1995 Land Cruiser II, Bundera LJ/RJ/KZJ 70/71/73/74/78
1985-1995 Land Cruiser II Prado LJ78
1991-1998 Land Cruiser 70 Series HZJ/FZJ/FJ/HDJ/PZJ 70/71/72/73/74/75/76/77 Series, SWB, MWB, Troopie, UTE
1999 & Newer Land Cruiser 70 Series HZJ/FZJ/HDJ/PZJ/VDJ/GRJ 70/71/73/74/76/79/79, SWB, MWB, Troopie, UTE
1990-1997 Toyota Land Cruiser HDJ80, HDJ81, HZJ80, FZJ80, FJ80
1998-2007 Toyota Land Cruiser 100 Series UZJ100, FZJ100, HDJ100
1998-2007 Toyota Land Cruiser HZJ105, FZJ105
1996-1997 Lexus LX450
1998-2007 Lexus LX470
Note: 2002 & older models are the smaller 27 spline pinion flange.
Carrier bearing
90366-50001 Nachi 50KB8301 msrp $65.71 note 50mm journals ( 90366-50001 is same dimensionally as 90366-50130 )
Outer pinion bearing
small 90366-30067 STA3072-1 msrp $65.71
Inner pinion bearing
BIG 90366-35087 TR070904-1-N msrp $101.25
front axle seal(LH) 90311-47013(replaces 47010 T0016)
front axle seal(RH) 90311-47027(replaces 47011 47012 47020 T0015)
Rear pinion seal (early1998-2002) 90311-38066 recess .210"
Rear pinion seal (2003~) 90311-41009
ring gear bolts(10) 71 ft/lb fsm
bearing caps(4) 63 ft/lb fsm
Driverside steel tube (4) 77 ft/lb fsm
aluminum lid(9) 34 ft/lb fsm
driveshaft(4) 59 ft/lb fsm
drain/fill plugs 36 ft/lb fsm
Deck height(Diff case) = 1.896" (8" low pinion is a larger 2.010")
The very common 8" pinion shim sizes/part numbers....
90564-35109 T=1.70 .0669" $3.52
90564-35110 T=1.73 .0681" $3.52
90564-35111 T=1.76 .0693" $3.52
90564-35112 T=1.79 .0705" $10.64
90564-35113 T=1.82 .0717" $3.52
90564-35114 T=1.85 .0728" $3.52
90564-35115 T=1.88 .0740" $3.52
90564-35116 T=1.91 .0752" $3.52
90564-35117 T=1.94 .0764" $3.52
90564-35118 T=1.97 .0776" $3.52
90564-35119 T=2.00 .0787" $3.52
90564-35120 T=2.03 .0799" $3.52
90564-35121 T=2.06 .0811" $3.52
90564-35123 T=2.09 .0823" $3.52
90564-35124 T=2.12 .0835" $3.52
90564-35125 T=2.15 .0846" $3.52
90564-35126 T=2.18 .0858" $3.52
90564-35127 T=2.21 .0870" $3.52
90564-35128 T=2.24 .0882" $3.52
90564-35129 T=2.27 .0894" $3.52
90564-35130 T=2.30 .0906" $3.52
90564-35131 T=2.33 .0917"
Solid collar final length~~1.866"
*********************************************************************************************************************************
*********************************************************************************************************************************
E-locker 8" LP (very common)
Wiring TRD elockers with an FZJ80 elocker ECU and switch
broken e-locker sidegear discussion........another alternate discussion
E-Locker re-assembly and CBPL
Installing an e-locker into a normal axle housing(drilling and tapping) 3rd Gen 4Runner E-locker Retrofit
adding a factory E-locker in a non E-locker quipped Tacoma(yotatech.com)
Retrofit Electric Locker
Diff lock indicator switch Toyota part number 84725-35010
E-Locker control box.....make your own
E-Locker 1.5 volt battery test....
(+ on 2 and - on 3 unlocks it.......(+ on 3 and - on 2 is to lock it.....) (note that pin 1 is empty)
proper clocking of "the notch".....In the locked position where the actual meshing of the teeth is considered the "12 oclock" position, the notch on the round gear will be at 6 oclock (straight down).
Needs to be verified.....When in the locked position, the round spur gear has a square notch that points in the "1 o'clock" direction....almost points to the vacuum port.
**********************************************************************************************************************
Below is a copy/paste from my friend Jim Hughes in New Mexico and is in regards to the retrofit e-lockers that are breaking
the sidegear(usually the passenger side goes first)...good info to know....
Zuk, I have attached pics of the side gear and axle damage. I did confirm the 2nd gen 4Runner 1989~95 (Coil Sprung) rear axle
shafts are approximately 7mm longer than the 1986~94 leaf sprung IFS axle shafts. This additional length should help from
twisting the side gear as the axle will go into the beefy part of the gear, not just the collar.
**********************************************************************************************************************
41110-35860 4.10 electric locking diff (verified with my own eyes on the box) $1425.90 retail (6-14-2011)
41110-3D280 4.30 electric locking diff (verified with my own eyes) $1293.21 retail
41110-3D010 4.56 electric locking diff $1293.21 retail
41201-69466 4.30 V6 ring/pinion verified $843.33 retail
41110-3D230 3.909 electric locking diff(verbal from Toyota parts-counter) $1422.35 retail
41110-3D220 3.58 electric locking diff(verbal from Toyota parts-counter) $1422.35 retail
outer pinion bearing
KOYO STA3072 verified Toyota part # 90366-30025 superceded by 9036630067 ($49.93 retail)
(crosses to a BR114 ....ebay seller is "parts-for-imports" (yellow star) $31.77 free ship
received a genuine koyo STA3072-9 (4 travel day delivery)...good find.
KOYO TR0607J-1 same verified
inner pinion bearing
TWB TR070904 same verified
KOYO TR070904-1-N cone/TR070904-1-9 cup (90366-35087 $91.40 retail)verified
carrier bearing
case side------KOYO TR100802-1 cone/TR100802-2 cup verified (90366-50007 $46.33 retail)
ring side BIG side------KOYO 32915JRYA1-N cone/32915JR-N cup (Toyota # 90366-75001 $29.44 retail) verified
Oil slinger(fan blade)---- for High pinions larger 29 spline verified 41214-60011 .....$6.12 retail
IF using the TRA0607RYR outer pinion bearing---solid collar = 1.815 + .084".....also, use 4 oil slingers total to space out the dust shield properly.
Toyota Transfer Indicator Switch 84222-12010 retails at $95.71 (exact Napa replacement is # NS6421 $22.49)
even better deal at RockAuto.com enter part number 201-1788 in Search bar $11.40 (Beck/Arnley)
also Autozone part # JA449 $23.50
Freeze plug 3/4"..... Dorman 555-012 .69 each O'reilly Auto Parts (for blocking off ABS port)
The very common 8" pinion shim sizes/part numbers....
90564-35109 T=1.70 .0669" $3.52
90564-35110 T=1.73 .0681" $3.52
90564-35111 T=1.76 .0693" $3.52
90564-35112 T=1.79 .0705" $10.64
90564-35113 T=1.82 .0717" $3.52
90564-35114 T=1.85 .0728" $3.52
90564-35115 T=1.88 .0740" $3.52
90564-35116 T=1.91 .0752" $3.52
90564-35117 T=1.94 .0764" $3.52
90564-35118 T=1.97 .0776" $3.52
90564-35119 T=2.00 .0787" $3.52
90564-35120 T=2.03 .0799" $3.52
90564-35121 T=2.06 .0811" $3.52
90564-35123 T=2.09 .0823" $3.52
90564-35124 T=2.12 .0835" $3.52
90564-35125 T=2.15 .0846" $3.52
90564-35126 T=2.18 .0858" $3.52
90564-35127 T=2.21 .0870" $3.52
90564-35128 T=2.24 .0882" $3.52
90564-35129 T=2.27 .0894" $3.52
90564-35130 T=2.30 .0906" $3.52
90564-35131 T=2.33 .0917"
*********************************************************************************************************************************
*********************************************************************************************************************************
8.2" 2010 4Runners/FJC
Vehicle Applications:
2010-2014 Toyota FJ Cruiser (All manual transmission models have OEM 3.90 ratio)
2010 & Newer Toyota 4Runner
2009 & Newer Lexus GX460
2009 & Newer Toyota Prado 150 Series
Outer pinion bearing
KOYO STA3574 90366-35157 (bigger than the V6 bearing)
Inner pinion bearing
KOYO ST4096 90366-40132 (bigger than the V6 bearing)
carrier bearing
90366-50130 (open diff) ( 90366-50001 is same dimensionally )
For the factory elocker, the right carrier bearing is 90366-50007 (TR100802-2)....left side is the larger 90366-75001
pinion seal 90311-44008 (XH0964E NOK)
crush sleeve 41231-35050
flanged pinion nut(large 43mm) 90179-22029 replaced by 90179-A0002
Companion flange 41204-35120
Ring gear bolts(12 quantity) 11mm flange style 90105-11061
Differential paper gasket part number 42181-60140
Differential paper gasket part number 42181-60140 Trail package
ring bolts (12) 71 per fsm
caps(4) 76 per fsm
pinion nut max 337
seal depth=0
pinion flange nut extra wide (43mm) 90179-22029 (90179-A0002)
lock indicator sw 30 ft/lb
diff carrier to axle housing (11) 38 ft/lb
drain and fill plugs--- 36 ft/lb
driveshaft bolts(4) ---- 65 ft/lb
(+ on 2 and - on 3 unlocks it.......(+ on 3 and - on 2 is to lock it.....) (note that pin 1 is empty)
*********************************************************************************************************************************
*********************************************************************************************************************************
8.4" Tacoma rear
Vehicle Applications:
1995.5-2014 Tacoma 4x4, Non E-Locker
1993-1998 T100
2000-2006 Tundra
2000-2007 Sequoia
2001-2004 Toyota Tacoma S-Runner
2005-2009 Toyota Tacoma X-Runner
Outer pinion bearing
KOYO HM88649-N cone/HM88610-N cup verified
Timken HM88649 555 cone/HM88610 555 cup verified
90368-34007 ($46.33 retail)
Inner pinion bearing
90366-40068 $101.34 retail (Koyo ST4595-N race/ST4095-N bearing) verified
carrier bearing
90366-51001($50.20 retail) (KOYO ST5186 both) verified (SKF BR135) Note that the factory journals are 51mm
pinion seal 90311-44007 (NOK BH4053G) ($16.32 retail)
crush sleeve 41231-34010 $23.65 retail
flanged pinion nut(big 30 spline) 90179-24012 ($1.89 retail) verified part number
Companion flange (60mm x 60mm) 41204-34010 ($147.40 retail) $97.01 at McGeorge Toyota
ring gear bolts(12)(12mm x 1mm flanged) 90901-05002 12 @ 4.39 each retail
Bearing Cap bolts(4 long bolts)90901-05003 4 @ 10.32 each retail
Differential paper gasket part number 42181-34011 retail $9.40
Drain plug (rear diff) part number 90341-18057 retail $11.15 (metal gasket= 12157-10010 $1)
Fill plug (rear diff) part number 90341-18006 retail $4.67 (metal gasket= 12157-10010 $1)
Solid collar final length...(.085" pinion shim behind the race)....about 2.321"
Pinion washer part numbers (screen snapshot)
ring (12) 92 ft/lb per fsm
brace cap (4) 83 per fsm
pinion seal 44007 installed flush per fsm
DO NOT use shims behind pinion head
*********************************************************************************************************************************
*********************************************************************************************************************************
8.75" Tacoma TRD rear
Vehicle Applications:
2016 & Newer Toyota Tacoma, Automatic with OEM locker
2016 & Newer Toyota Tacoma, Manual with or without OEM locker
2016 & Newer Toyota Hilux Revo With or without OEM Locker
Outer pinion bearing
STN3580/ST3680 KOYO 90366-T0062 (offroad package 8.75")
Inner pinion bearing
TRD091004/same KOYO 90366-T0065 (offroad package 8.75")
carrier bearing
BIG STB5083/STA5383 KOYO 90366-T0068
SMALL STA5076/STA4076 KOYO 90366-T0071
pinion seal XH1691E NOK 90311-T0065 $18.93 verified
crush sleeve 41231-71010
flanged pinion nut(large 43mm)90179-A0002
Companion flange 41204-0K110
ring gear bolts(12)90105-12365
Differential paper gasket part number 42181-KK010
Drain plug (rear diff) part number 90341-18057 (metal gasket= 12157-10010)
Fill plug (rear diff) part number 90341-A0002 (metal gasket= 12157-10010 $1)
ring bolts(12) 92 per testing
caps(4) 84 per testing
Black connector(Lock Indicator) 84222-0K010
Blue connector 82824-0K060 $35
oem pinion seal 90311-T0065 $25
8.75 paper gasket 42181-KK010
*********************************************************************************************************************************
*********************************************************************************************************************************
CLAM 7.5" HP for 96~02 4Runners/95.5~2004 Tacos
Vehicle Application:
1996-2002 Toyota 4Runner 4wd 4x4 IFS Front
1995-1/2-2004 Toyota Tacoma 4wd 4x4 IFS Front
2000-2006 Toyota Tundra 4wd 4x4 IFS Front
2001-2007 Toyota Sequoia 4wd 4x4 IFS Front
1996-2002 Toyota Landcruiser Prado 90 4wd 4x4 IFS Front
Outer pinion bearing
90366-30022 $45.43 retail (new number 90366-30078-77)
Inner pinion bearing
90366-35023 $100.13 retail (new number 90366-35023-77)
carrier bearings
90368-50006 $47.49 retail each Koyo STB5080
carrier bearing for the ARB RD90 = LM503310/LM503349(race/bearing)
pinion seal 90311-38066 ($12.56 retail)
Seal-----driver left side axle stub seal(skinny one) 90311-47027(replaces 47011 47012 47020 T0015) ($16.18 retail) (BH5320I)
Seal-----right side passenger steel tube extension seal(outer end of steel tube)(fat one) 90311-47013(replaces 47010 T0016) (BH5321F) ($17.61 retail)
flanged pinion nut 90179-18020 ($2.18 retail) (18mm threads) verified
front pinion flange 41204-35060 ($119.18 retail) (60mm x 60mm)
crush sleeve 41231-22010 ($15.17 retail)......(crush final length~2.188")
NO TRUETRACS IN THE CLAMS(post #217)
Beware of 3rd gen Runners (limiteds) with full time 4wd.....elockers will interfere with the long axle on passengerside(steel tube) ...will need .070" spacer on tube.
ring 10 bolts 70 ft/lb
lid 10 bolts ("11" stamped on head bolt) 51 ft/lb
steel arm 4-E14 bolts 59 ft/lb
Pinion seal is 90311-38066....recessed .170
Driverside axle seal.............. 90311-47027 0 recess
fill plug 90341-24014 copper washer 90430-24003
DON'T FORGET to grind the 2 nubs down for the elocker magnet/stop tabs and check for interference.
some ring/pinions might need some minor "flapper love" to clear the stop tabs ....use "slip fit" bearing to avoid the love. OR cut 1/4" off the stop tabs.
use 8.4" inner race to seat the magnet assembly tap tap
The thicker 7.5" pinion shim part numbers/sizes....
90201-35434 .0882" MARK 01, T=2.24 1 $6.05
90201-35435 .0894" MARK 02, T=2.27 1 $6.05
90201-35436 .0906" MARK 03, T=1.76 1 $6.05
90201-35437 .0917" MARK 04, T=1.79 1 $6.05
90201-35396 .0929" MARK 05, T=2.36 1 $5.77
90201-35397 .0941" MARK 06, T=1.85 1 $5.77
90201-35398 .0953" MARK 07, T=2.42 1 $5.77
90201-35399 .0965" MARK 08, T=2.45 1 $5.77
90201-35400 .0976" MARK 09, T=2.48 1 $5.77
90201-35401 .0988" MARK 10, T=2.51 1 $5.77
90201-35402 .1000" MARK 11, T=2.54 1 $5.77
90201-35403 .1012" MARK 12, T=2.57 1 $5.77
90201-35404 .1024" MARK 13, T=2.60 1 $5.77
90201-35438 .1035" MARK 14, T=2.63 1 $5.77
90201-35439 .1047" MARK 15, T=2.66 1 $5.77
90201-35440 .1059" MARK 16, T=2.69 1 $5.77
90201-35441 .1071" MARK 17, T=2.72 1 $5.77
*********************************************************************************************************************************
*********************************************************************************************************************************
CLAM 8" HP for 2003~2014 Runners/2005+ Tacos
Vehicle Applications:
2003-2014 Toyota 4Runner
2003-2009 Lexus GX470
2003-2014 Toyota Hilux Surf
2005-2014 Toyota Tacoma
2007-2014 Toyota FJ Cruiser
2002-2009 Toyota Landcruiser
Prado 120
2010-2014 Lexus GX460
2009-2014 Toyota Landcruiser
Prado 150
2005-2014 Toyota Hilux
2005-2014 Toyota Fortuner
Small outer pinion bearing
KOYO STA3072 verified Toyota part # 90366-30025 superceded by 9036630067 ($49.93 retail)
(crosses to a BR114 ....ebay seller is "parts-for-imports" (yellow star) $31.77 free ship
received a genuine koyo STA3072-9 (4 travel day delivery)...good find.
Koyo TR0607 J-1/TR0607 J-1
BIG Inner pinion bearing
KOYO TR070904-1-N cone/TR070904-1-9 cup (90366-35087 $91.40 retail)verified
carrier bearings
Koyo STA5383 90366-53004 $56.00 JT's...............
Seal-----pinion 90311-41009 ($22.46 retail)
flanged pinion nut 29 spl 90177-22003 ($2.57 discounted) wide flange style, 22mm thread dia
crush sleeve 41231-35040 ($15.85 retail)......(crush final length~1.414")
Seal-----driver left side axle stub seal(skinny one) 90311-47027(replaces 47011 47012 47020 T0015) ($16.18 retail) (BH53201)
Seal-----passenger right steel tube extension seal(outer end of steel tube)(fat one) 90311-47013(replaces 47010 T0016) (BH5321F)($17.61 retail)
solid collar = 1.387" + .032" = 1.419" (1.413" observed)
NO TRUETRACS IN THE CLAMS(post #217)
2010-2017 fsm starts at page 1264
FSM............ring (10) flange bolts 85 ft/lb
FSM............lid 10 bolts 37 ft/lb (2010~2017 models) that what it says.
****************Drill grommet hole 2.300" below lip....try 2.7~3.0 inches
***************Clearance the 3 notches inside the bowl.
also, clearance the steel tab itself...mostly on the end....shorten it up
drain plug 48 ft/lb
fill plug 29
steel tube(passenger side) 4 bolts 81 ft/lb (2010~2017 models) E14 torx socket
Passenger side axle seal(on steel tube) factory measured at ~.220" Use special flat seal driver with IFS 4 cyl washer plate (.106 + .107")
pinion nut......273 ft/lb max seal depth(41009)= .170" (.154~.184")
late model clams recess the seal(41015) .120~130" as measured/verified.
FIPG 1281
pinion flange runout max= .00591"
pinion flange (3rd gen Tacos) 41204-71030
carrier bearings---STA5383 90366-53004
pinion seal-- NOK BH6832E ( late model use 90311-41015 XH1701H pinion seal, depth is verified .110")
stub seal (driver side)----NOK BH5320F (National 710596 appears to be genuine factory #)
steel tubular arm seal (passenger side) BH5321F 90311-47013 or BH5321H 90311-47026 for the late model ones
The very common 8" pinion shim sizes/part numbers....
90564-35109 T=1.70 .0669" $3.52
90564-35110 T=1.73 .0681" $3.52
90564-35111 T=1.76 .0693" $3.52
90564-35112 T=1.79 .0705" $10.64
90564-35113 T=1.82 .0717" $3.52
90564-35114 T=1.85 .0728" $3.52
90564-35115 T=1.88 .0740" $3.52
90564-35116 T=1.91 .0752" $3.52
90564-35117 T=1.94 .0764" $3.52
90564-35118 T=1.97 .0776" $3.52
90564-35119 T=2.00 .0787" $3.52
90564-35120 T=2.03 .0799" $3.52
90564-35121 T=2.06 .0811" $3.52
90564-35123 T=2.09 .0823" $3.52
90564-35124 T=2.12 .0835" $3.52
90564-35125 T=2.15 .0846" $3.52
90564-35126 T=2.18 .0858" $3.52
90564-35127 T=2.21 .0870" $3.52
90564-35128 T=2.24 .0882" $3.52
90564-35129 T=2.27 .0894" $3.52
90564-35130 T=2.30 .0906" $3.52
90564-35131 T=2.33 .0917"
*********************************************************************************************************************************
*********************************************************************************************************************************
CLAM 9" aluminum for 07+ Tundras/08 200series/LX570
Vehicle Applications:
2007-2018 Toyota Tundra 9" Front Diff (T9R)
2008-2018 Toyota Land Cruiser 200 Series VDJ200 URJ200 9" Front Diff (T9R)
2008-2018 Lexus LX570 9" Front Diff (T9R)
Small outer pinion bearing
90363-35063 JT's $86 ..... Nachi TJ8399 / 35DTW0854
BIG Inner pinion bearing(double ball bearing cage)
90366-40114 JT's $108 .....Nachi 40KD903SLT CLK / 40KD903 CLK
carrier bearings(2)
90366-58013 JT's $55 ...... KOYO ST5889/ST5889
Seal-----pinion 90311-46006 NOK XH0533E (before May of 2015)
flanged pinion nut 90179-22029
crush sleeve 41231-34040 JT's $13.64
Seal-----driver.....left side axle stub seal(skinny one) 90311-47027(replaces 47011 47012 47020 T0015) ($16.18 retail) (BH53201)
Seal-----passenger..... right side aluminum tube extension seal(outer end of aluminum tube)(fat one) 90311-47013(replaces 47010 T0016) (BH5321F)($17.61 retail)
no solid collar option yet
63.8 pounds bare....no mounts no arm
ring bolts (12) 101 per fsm
Case (11) 48 per fsm verified
fill plug 29 ft/lb
drain plug 29
tube assembly(4 bolts 17mm) 48 ft/lb per pdf
pinion nut 333 ft/lb max
seal depth .221~.259" verified (.250 measured)
PPL 27~30 verified
confusion on FSM...15~21 and 27~30 preloads mentioned. (new)
outer PB EM6733 (90363-35063) .... Nachi TJ8399 / 35DTW0854
inner PB Nachi 40KD903 SLT CLK (90366-40114)
CB (2) Koyo ST5889 (90366-58013)
RH seal (end of tube) 90311-47026
LH seal (small one) 90311-47027
pinion seal 90311-46006 (<---May of 2015 models) NOK XH0533E
pinion seal 90311-46007 (May of 2015---> models) NOK XH0533G
Drill 29/64" hole 3.25" from the lip along the seam.
use TJM drill(.0463") bit for easier fitment.
Ideal spot(visually verified)...4.40" under the bolt hole (same as 4.40" down the seal and .5~.8" to the left)
*********************************************************************************************************************************
*********************************************************************************************************************************
8" E-locker high Pinion
Outer pinion bearing
KOYO STA3072 verified Toyota part # 90366-30025 superceded by 9036630067 ($49.93 retail)
(crosses to a BR114 ....ebay seller is "parts-for-imports" (yellow star) $31.77 free ship
received a genuine koyo STA3072-9 (4 travel day delivery)...good find.
KOYO TR0607J-1 same verified
Inner pinion bearing
90366-35087 ($91.40 retail) verified
carrier bearing
case side------KOYO TR100802-1 cone/TR100802-2 cup verified (90366-50007 $46.33 retail)
ring side BIG side------KOYO 32915JRYA1-N cone/32915JR-N cup (Toyota # 90366-75001 $29.44 retail) verified
flanged pinion nut (27 spline count, 20mm thread dia)) 90179-20018 $3.23 retail verified
oil retainer 41115-35010 $3.83 retail
Oil slinger(fan blade)---- for High pinions smaller 27 spline..... 41214-60010 .....$15.83 retail
Oil slinger(fan blade) for High pinions bigger 29 spline version 41214-60011 .....$6.12 retail
oil seal 90311-38047 $8.03 retail
Solid collar final length ~1.874"
(+ on 2 and - on 3 unlocks it.......(+ on 3 and - on 2 is to lock it.....) (note that pin 1 is empty)
The very common 8" pinion shim sizes/part numbers....
90564-35109 T=1.70 .0669" $3.52
90564-35110 T=1.73 .0681" $3.52
90564-35111 T=1.76 .0693" $3.52
90564-35112 T=1.79 .0705" $10.64
90564-35113 T=1.82 .0717" $3.52
90564-35114 T=1.85 .0728" $3.52
90564-35115 T=1.88 .0740" $3.52
90564-35116 T=1.91 .0752" $3.52
90564-35117 T=1.94 .0764" $3.52
90564-35118 T=1.97 .0776" $3.52
90564-35119 T=2.00 .0787" $3.52
90564-35120 T=2.03 .0799" $3.52
90564-35121 T=2.06 .0811" $3.52
90564-35123 T=2.09 .0823" $3.52
90564-35124 T=2.12 .0835" $3.52
90564-35125 T=2.15 .0846" $3.52
90564-35126 T=2.18 .0858" $3.52
90564-35127 T=2.21 .0870" $3.52
90564-35128 T=2.24 .0882" $3.52
90564-35129 T=2.27 .0894" $3.52
90564-35130 T=2.30 .0906" $3.52
90564-35131 T=2.33 .0917"
*********************************************************************************************************************************
*********************************************************************************************************************************
Landcruiser rear 9.5" .... 1968~1997
Vehicle Applications:
1969-1983 FJ40 front or rearFJ45 front or rear
1968-1979 FJ55 front or rear
1981-1987 FJ60 front or rear
HJ60 front or rear
1988-1990 FJ62 front or rear
BJ70 Leaf Sprung Only (not coil sprung)
1990-1992 Landcruiser FJ80 Rear
1993-1997 Landcruiser FZJ80 Rear
1990-1997 Landcruiser HDJ80 Rear
1990-1997 Landcruiser HZJ80 Rear
1990-1997 Landcruiser HZJ81 Rear
Outer pinion bearing(race/bearing)
90366-30038 ...... verified
do not use aftermarket Toyota Landcruiser bearings with the possible exception of those bearing kits from sor.com
Inner pinion bearing(race/bearing)
90366-40059 verified
Carrier bearing(race/bearing)
90366-50177 .... verified
Monster sized carrier bearings used in the E-Locker rears--- 90366-60002
********SPECIAL NOTE(1-18-2015)***************SPECIAL NOTE*************SPECIAL NOTE***********************
The MONSTER E-LOCKER CARRIER BEARINGS
Some master install kits might have the WRONG monster carrier bearing for the 9.5" E-Lockers.
correct bearing/race= 32012JR-N(bearing)............32012J/18-N (race) These are the Genuine Toyota replacement bearings
Dimensionally inferior bearing /race is 32012JR/18-Y(bearing)...........32012/18-Y(race)
The inferior bearing is dimensionally wrong....washer plates will not work with them.
Width diameter is .020" thicker and cage sticks out too far.
So, it seems that if the carrier bearing part number ends with a "Y" then it won't work.....
If it ends in "N" then all is good.
CARRIER BEARING for ring gear side when installing Eaton or Harrop elocker. Use 90366-50177 (stamped 570064-1/32010J) due to the the larger radius on the journal
of the elocker. Using other bearings will result in an air gap of about .020" (not fully seated 100%). 11-21-21
If you have to disassemble the elocker center carrier(which has the sidegears and spiders inside) then you need to remove the stubborn E10(I think) torx bolts(8 of them).
3 of them are with longer pins(41343-60010) and 5 are the short threaded bolts(90109-10091). Retorque to 43 foot/pounds(per FSM) with red loctite. Good luck getting the
originals off without twisting off the heads.
(+ on 2 and - on 3 unlocks it.......(+ on 3 and - on 2 is to lock it.....) (note that pin 1 is empty)
*********************************************************************************************************************************
crush sleeve 41231-60030 $16.95 retail
pinion seal 90311-38047 $9.77 retail(F7134 in tiny print on rubber)
FSM specs.....
ring gear 81
bearing caps..... 58 for open diff, 83 for elocker version
new PPL 11~17
sidegear washer plate shims(spider gear backlash spec = .002"~.008")
.063" (41361-40021)
.067" (41362-40021)
.071" (41363-40021)
update....5-31-21......another 1975ish 3rd...working numbers.....with .014" behind the inner race, the solid collar length was trimmed to 2.1655".
Solid collar final length (1990 and older 27 spline pinions)..... 2.189" a little higher than usual
Solid collar final length (91 and newer, 90366-30038 outer pinion bearing)..... 2.111" this is the norm
Solid collar final length (91 and newer, using aftermarket outer 30306 pinion bearing)..... 2.135~2.137" this is the norm
Solid collar final length (91 and newer, using optional genuine factory 90366-30038 outer pinion bearing)..... ~2.117" a little higher than usual
Old FJ40 Cruisers(1978ish) that have the built-in solid collar on the pinion shaft....with .011" behind the race use .123" pinion step shim 7-23-16
(+ on 2 and - on 3 unlocks it.......(+ on 3 and - on 2 is to lock it.....) (note that pin 1 is empty)
*********************************************************************************************************************************
*********************************************************************************************************************************
*********************************************************************************************************************************
*********************************************************************************************************************************
100 series(98~06).......200 series (07 on )
ring bolts(12) 101 per fsm
caps (4) 76
drain and fill plugs 36 ft/lb
diff nuts(10) 53 ft/lb
driveshaft (4) 52 ft/lb
pinion nut 325 max
PPL 10~14 in/lb start new (8~12 used)
100 series rigs(98~06)................
9.5" Outer Pinion Bearing
90366-30071
9.5" Inner Pinion Bearing
90366-40088
REAR 9.5" Carrier Bearings
open.........90366-50177
elocked......90366-60002
1998-2002..... 27 spline use 38066 seal
2003-08/2005.....29 spline 41009 seal
09/2006 on.... rear pinion seal 32 spline 90311-45028 XH0563E recess 1.2mm
stock crush sleeve length in a stock 100 series with stock gears and bearings is about 2.112"
Solid collar on a 100 series that was regeared to 4.88 with the beefy 32 spline pinion and 200 series pinion bearings....1.950" collar + .025" shim (observed)
200 series rigs(2007 on)(LX570)................
Outer Pinion Bearing (32 spline) 90366-33006 $52 (09/2006 on) NSK..... STF R33-6g/STF R33-6g visually verified.
Inner Pinion Bearing 90366-40111 $84 (09/2006 on) NSK......STF R40-101g/STF R40-101g visually verified
Carrier Bearings (2) 90366-50177 $55
09/2006- rear pinion seal 32 spline 90311-45028 XH0563E recess 1.2mm
05/2015- rear pinion seal 90311-45036
non-elocker version....carrier bearings...old # 90366-50054 replaced by 90366-50177(use this)
alternate C.B. is 32010j 90368-50024
*********************************************************************************************************************************
*********************************************************************************************************************************
"200 and 1/2 series" (2015 Landcruiser Heritage and newer)
2015 and newer
can still put gears in both ends. Locker in rear is still ok. 3-19-21
Can put locker in front if substitute a Tundra 9" front clam in place.
TECH NOTE:
12:25
· LC200 2016+ US MODELS AND OVERSEAS “LOADED” PACKAGE WENT TO 8 SPEED AUTO AND 3.31 RATIO
· REAR: CAN NOT BE REGEARED WITHOUT NEW DROPOUT!!!!!! (Any LC 9.5 or Tundra 9.5 is interchangeable)
· Pinion in casting shifted - like a Dana 61 to allow for pinion size (3.31 Casting only)
· Carrier is standard and is 32 spline RD152 / HAR-T9.5 works
· FRONT: REQUIRES 3.90 AND UP CARRIER
· HAR-T9R / 14217-1 / A11092 OR RD151 DOES NOT WORK W/ 3.31 RATIO
Summary: LC200 3.31 can be locked in the rear but not regeared with out drop out / Front cannot be locked without regear
Best Regards,
Chase Perry
*********************************************************************************************************************************
*********************************************************************************************************************************
Other stuff
Tacoma V6 idler pulley-----SKF 6301-2ZJ SHIELDED bearing....SKF 6301-2RS $8.99
Freeze plug 3/4"..... Dorman 555-012 .69 each O'reilly Auto Parts (for blocking off ABS port)
Fan clutch (HD green 3.4L towing package 08921-04950)
79~85 pinion head length ~ 1.534" (4 cyl)
86~95 pinion head length ~ 1.668" (V6'ers)
pinion seal----common 8" rear (1)90311-38047 8.00 retail (79~95) or Napa #19630 is a good quality one, 1177, F7134.
pinion seal----29 spline rubberized black 90311-41009 (BH6832E) $17.56 retail
pinion seal----8.4" rubberized black 90311-44007 (BH4053G) $17.58 retail
washer----thick hardened (used behind the pinion nut on 8" 3rds, 27 splines) 90201-20005 $2.54 retail
pinion nut----m20x1.5 flanged (30mm 27 spline) 90179-20018 verified $5.29 retail
verified
pinion nut----m20x1.5 normal (30mm 27 spline) 90179-20001 ...... $3.48 retail
pinion nut----m22x1.5 flanged (Narrow flange style 29 spliners) 90179-22016 ...... $3.42 retail
axle seal----common rear 8" inner (2)90310-50001 (superceded by 9031050006 $6.48 retail each) (79~95)
axle seal----IFS 7.5" front 3rd (2 needed for non-vacuum type) 90311-35032 $14.08 retail (86~95) verified
axle stub seal----Supra IRS rear-end 7.5"(2 needed) 90311-38011 (typically 1982~86 Supra MK2 models)verified
pinion seal----Supra IRS rear-end 7.5" 14767 (typically 1982~86 Supra MK2 models)
pinion seal----Supra IRS rear-end 7.5" genuine OEM is 90311-38010 verified
crush sleeve----IFS 7.5" front 41231-22010 $13.80 retail(86~95)
crush sleeve----4 cyl 8" rear 3rds(79~95) 41231-40011 $23.64 retail
crush sleeve----V6 3rd(88~95) 41231-24010 $17.15 retail
crush sleeve----LC (9.5" rear 3rd) 41231-60020 $27.06 retail
ring gear bolts---- 11mm x 1mm 90101-11353 ($1.03 each retail)
Oil slinger(flat)---- for low pinions 41214-26010 smaller 27 spline $10.23 retail
Oil slinger(flat)---- for low pinions 41214-26011 larger 29 spline diameter verified
Oil slinger(fan blade)---- for High pinions smaller 27 spline 41214-60010 $15.83 retail
Oil slinger(fan blade)---- for High pinions larger 29 spline verified 41214-60011 .....$6.12 retail
spanner adjuster ring----V6 larger version 41315-35020 $13.78 retail
Front outer axle spindle brass bushing solid----- 90999-70067 verified with my eyeballs
shaft snap rings(for mini-truck and FJ60/62)holds the axle inside the birf cup # 90520-27091
91 and newer Cruisers have the larger 50mm case journals
Landcruiser 9.5" crosspin shaft 41342-55010
Landcruiser 9.5" sidegear washer .069" 41361-60021
shifting selonoid kit for autos on older Yotas(86~95)
Axiom Automotive Technologies....1360 Ingleside Rd.....Norfolk, VA 23502....800-622-6997 (kit#97420K)
On-line French place................. 123Bearing.com
TR100802-2............V6 CB...........32.50retail...........JT
TR070904-1-9-LFT..V6 big PB.......30.44 123bearing (JT's $64 search 90366-35028 )
STA3072-9LFT-KOYO......(JT 90366-30025) V6 outer PB.....58.31 (better deal on Ebay.....crosses to a BR114 $31.77 free ship, Ebay seller "parts-for-imports")
STA5383...(JT 90366-50004)...........(8" clam CB).....56.00retail(123Bearing $34.96)
ST5186....(JT 90366-51001)........T100 CB.........54.95retail (also crosses to a SKF BR135)
30308......JT.......... Landcruiser inner pinion bearing 37.00retail
30306......JT.......... Landcruiser OUTER pinion bearing 33.00retail
32010X......JT.......... conversion bearing 50mm 29.00retail
8.75" pinion seal XH1691E.......JT(90311-T0065)........ $23 retail
On-line wholesale Toyota pricing(my new fav) McGeorge Toyota OnlineParts
On-line wholesale Toyota pricing(20~25% savings) Camelback Toyota-Scion Parts
On-line wholesale Toyota pricing(20~25% savings) ToyotaPartsDeal.com
On-line wholesale Toyota pricing(20~25% savings) ToyotaPartsOverstock.com
*********************************************************************************************************************************
7.5" IFS
*********************************************************************************************************************************
Front 7.5" IFS carrier bearing shim (washer plate) part numbers
mm inches 4 cyl PN V6 cyl PN
2.58 .1016 90201-65007 90201-50003
2.61 .1028 90201-65008 90201-50004
2.64 .1039 90201-65009 90201-50005
2.67 .1051 90201-65010 90201-50006
2.70 .1063 90201-65011 90201-50007
2.73 .1075 90201-65012 90201-50008
2.76 .1087 90201-65013 90201-50009
2.79 .1098 90201-65014 90201-50010
2.82 .1110 90201-65015 90201-50011
2.85 .1122 90201-65016 90201-50012
2.88 .1134 90201-65017 90201-50013
2.91 .1145 90201-65018 90201-50014
2.94 .1157 90201-65019 90201-50015
2.97 .1169 90201-65020 90201-50016
3.00 .1181 90201-65021 90201-50017
3.03 .1193 90201-65022 90201-50018
3.06 .1204 90201-65023 90201-50019
3.09 .1216 90201-65024 90201-50020
3.12 .1228 90201-65025 90201-50021
3.15 .1240 90201-65026 90201-50022
3.18 .1252 90201-65027 90201-50023
3.21 .1264 90201-65028 90201-50024
3.24 .1276 90201-65029 90201-50025
The thicker 7.5" pinion shim part numbers/sizes....
90201-35434 .0882" MARK 01, T=2.24 1 $6.05
90201-35435 .0894" MARK 02, T=2.27 1 $6.05
90201-35436 .0906" MARK 03, T=1.76 1 $6.05
90201-35437 .0917" MARK 04, T=1.79 1 $6.05
90201-35396 .0929" MARK 05, T=2.36 1 $5.77
90201-35397 .0941" MARK 06, T=1.85 1 $5.77
90201-35398 .0953" MARK 07, T=2.42 1 $5.77
90201-35399 .0965" MARK 08, T=2.45 1 $5.77
90201-35400 .0976" MARK 09, T=2.48 1 $5.77
90201-35401 .0988" MARK 10, T=2.51 1 $5.77
90201-35402 .1000" MARK 11, T=2.54 1 $5.77
90201-35403 .1012" MARK 12, T=2.57 1 $5.77
90201-35404 .1024" MARK 13, T=2.60 1 $5.77
90201-35438 .1035" MARK 14, T=2.63 1 $5.77
90201-35439 .1047" MARK 15, T=2.66 1 $5.77
90201-35440 .1059" MARK 16, T=2.69 1 $5.77
90201-35441 .1071" MARK 17, T=2.72 1 $5.77
*********************************************************************************************************************************
8" IFS
*********************************************************************************************************************************
100 series Landcruisers 1998-2007
Front 8" IFS (washer plates)
Part Number inches mm ID el prico
90201-52001 .1016 T=2.58, MARK 01 X $5.93
90564-46014 .1024 T=2.60, MARK 32 X $15.58
90564-46015 .1031 T=2.62, MARK 33 X $10.44
90201-52003 .1039 T=2.64, MARK 03 X $5.93
90564-46016 .1047 T=2.66, MARK 34 X $10.44
90564-46017 .1055 T=2.68, MARK 35 X $10.44
90201-52005 .1063 T=2.70, MARK 05 X $7.04
90564-46018 .1071 T=2.72, MARK 36 X $12.41
90564-46019 .1079 T=2.74, MARK 37 X $12.41
90201-52007 .1087 T=2.76, MARK 07 X $7.04
90564-46020 .1094 T=2.78, MARK 38 X $12.41
90564-46021 .1102 T=2.80, MARK 39 X $12.41
90201-52009 .1110 T=2.82, MARK 09 X $7.04
90564-46022 .1118 T=2.84, MARK 40 X $12.41
90564-46023 .1126 T=2.86, MARK 41 X $12.41
90201-52011 .1134 T=2.88, MARK 11 X $7.04
90564-46024 .1142 T=2.90, MARK 42 X $12.41
90564-46025 .1150 T=2.92, MARK 43 X $12.41
90201-52013 .1157 T=2.94, MARK 13 X $7.04
90564-46026 .1165 T=2.96, MARK 44 X $12.41
90564-46027 .1173 T=2.98, MARK 45 X $12.41
90201-52015 .1181 T=3.00, MARK 15 X $7.04
90564-46028 .1189 T=3.02, MARK 46 X $12.41
90564-46029 .1197 T=3.04, MARK 47 X $12.41
90201-52017 .1204 T=3.06, MARK 17 X $7.04
90564-46030 .1213 T=3.08, MARK 48 X $12.41
90564-46031 .1220 T=3.10, MARK 49 X $12.41
90201-52019 .1228 T=3.12, MARK 19 X $7.04
90564-46032 .1236 T=3.14, MARK 50 X $12.41
90564-46033 .1244 T=3.16, MARK 51 X $12.41
90201-52021 .1252 T=3.18, MARK 21 X $7.04
90564-46034 .1260 T=3.20, MARK 52 X $12.41
90564-46035 .1268 T=3.22, MARK 53 X $12.41
90201-52023 .1276 T=3.24, MARK 23 X $7.04
90564-46036 .1283 T=3.26, MARK 54 X $12.41
90564-46037 .1291 T=3.28, MARK 55 X $12.41
90201-52025 .1299 T=3.30, MARK 25 X $7.04
90564-46038 .1307 T=3.32, MARK 56 X $12.41
90564-46039 .1315 T=3.34, MARK 57 X $12.41
90201-52027 .1323 T=3.36, MARK 27 X $7.04
90564-46040 .1331 T=3.38, MARK 58 X $12.41
90564-46041 .1339 T=3.40, MARK 59 X $12.41
90201-52029 .1346 T=3.42, MARK 29 X $7.04
90564-46042 .1354 T=3.44, MARK 60 X $12.41
90564-46043 .1362 T=3.46, MARK 61 X $12.41
90201-52031 .1370 T=3.48, MARK 31 X $7.04
The very common 8" pinion shim sizes/part numbers....
90564-35109 T=1.70 .0669" $3.52
90564-35110 T=1.73 .0681" $3.52
90564-35111 T=1.76 .0693" $3.52
90564-35112 T=1.79 .0705" $10.64
90564-35113 T=1.82 .0717" $3.52
90564-35114 T=1.85 .0728" $3.52
90564-35115 T=1.88 .0740" $3.52
90564-35116 T=1.91 .0752" $3.52
90564-35117 T=1.94 .0764" $3.52
90564-35118 T=1.97 .0776" $3.52
90564-35119 T=2.00 .0787" $3.52
90564-35120 T=2.03 .0799" $3.52
90564-35121 T=2.06 .0811" $3.52
90564-35123 T=2.09 .0823" $3.52
90564-35124 T=2.12 .0835" $3.52
90564-35125 T=2.15 .0846" $3.52
90564-35126 T=2.18 .0858" $3.52
90564-35127 T=2.21 .0870" $3.52
90564-35128 T=2.24 .0882" $3.52
90564-35129 T=2.27 .0894" $3.52
90564-35130 T=2.30 .0906" $3.52
90564-35131 T=2.33 .0917"
front axle seal(LH) 90311-47013(replaces 47010 T0016)
front axle seal(RH) 90311-47027(replaces 47011 47012 47020 T0015)
Rear pinion seal (early1998-2002) 90311-38066
Rear pinion seal (2003~) 90311-41009
carrier bearings..........90366-50001 (Nachi 50KB8301) ( 90366-50130 is same dimensionally )
pinion bearing(BIG) 90366-35087
pinion bearing (small) 90366-30067
for a 1986 Supra(MA70L-BJMZA)
90311-38010 pinion seal
90311-43001 (x2) side gear shaft seal replaced by 90311-43009
90366-30025 outer pinion bearing
90366-35028 inner pinion bearing
41204-35040 companion flange (27 spline normally)
100 series
original 27 spline seal tap flush based on observation(about .210~.235" below lip)
pinion seal is 90311-38066
29 spline pinions use the 41009 seal recess .170"
ring (10) 71 fsm
caps(4) 63+ fsm 12-18-17
cover (9) 34+ fsm
diff tube(4 17mm bolts) 77 ft/lb
passengerside front drop
47027 passengerside skinny seal verified
47013 driverside big seal (axletube end ) verified
29 spline flange needs dust cover 41252-60011
Eaton EAT14219 .....grind slots in bearing cap ~.530"
*********************************************************************************************************************************
7.5" CLAM
*********************************************************************************************************************************
Tacoma front carriers(common from 1995.5 to 2004 Tacoma and 1995.5 to 2002 Runners)
Front clamshell IFS 7.5" side washer plates
mm inches Part Number
2.01 .0791" 90564-50092
2.04 .0803" 90564-50093
2.07 .0815" 90564-50094
2.10 .0827" 90564-50095
2.13 .0839" 90564-50096
2.16 .0850" 90564-50097
2.19 .0862" 90564-50098
2.22 .0874" 90564-50099
2.25 .0886" 90564-50100
2.28 .0898" 90564-50101
2.31 .0909" 90564-50102
2.34 .0921" 90564-50103
2.37 .0933" 90564-50104
2.40 .0945" 90564-50105
2.43 .0957" 90564-50106
2.46 .0969" 90564-50107
2.49 .0980" 90564-50108
2.52 .0992" 90564-50109
2.55 .1004" 90564-50110
2.58 .1016" 90564-50111
2.61 .1028" 90564-50112
2.64 .1039" 90564-50113
2.67 .1051" 90564-50114
2.70 .1063" 90564-50115
2.73 .1075" 90564-50116
2.76 .1087" 90564-50117
2.79 .1098" 90564-50118
The thicker 7.5" pinion shim part numbers/sizes....
90201-35434 .0882" MARK 01, T=2.24 1 $6.05
90201-35435 .0894" MARK 02, T=2.27 1 $6.05
90201-35436 .0906" MARK 03, T=1.76 1 $6.05
90201-35437 .0917" MARK 04, T=1.79 1 $6.05
90201-35396 .0929" MARK 05, T=2.36 1 $5.77
90201-35397 .0941" MARK 06, T=1.85 1 $5.77
90201-35398 .0953" MARK 07, T=2.42 1 $5.77
90201-35399 .0965" MARK 08, T=2.45 1 $5.77
90201-35400 .0976" MARK 09, T=2.48 1 $5.77
90201-35401 .0988" MARK 10, T=2.51 1 $5.77
90201-35402 .1000" MARK 11, T=2.54 1 $5.77
90201-35403 .1012" MARK 12, T=2.57 1 $5.77
90201-35404 .1024" MARK 13, T=2.60 1 $5.77
90201-35438 .1035" MARK 14, T=2.63 1 $5.77
90201-35439 .1047" MARK 15, T=2.66 1 $5.77
90201-35440 .1059" MARK 16, T=2.69 1 $5.77
90201-35441 .1071" MARK 17, T=2.72 1 $5.77
7.5" clamshell pinion seal----old # 90311-38049.....6-16-2013---new superceded # 90311-38066 (retail $12.18)
oem range to drive seal down below the surface is .165"~.189"
*********************************************************************************************************************************
8" CLAM
*********************************************************************************************************************************
4Runner front clams from 2003 to 2009 models
Tacoma from 2005 to 2015
Front clamshell IFS 8" side washer plates
left side(bowl) is solid washer plate
right side(lid) has 12 holes
(Placed in order by thickness not part number)
Part number mm inches Retail
90564-50184 T=1.58, .0622" LH 1 $11.31
90564-50124 T=1.60, .0630" LH 1 $9.05
90564-50185 T=1.62, .0638" LH 1 $9.05
90564-50186 T=1.64, .0646" LH 1 $9.05
90564-50126 T=1.66, .0654" LH 1 $9.05
90564-50187 T=1.68, .0661" LH 1 $11.31
90564-50188 T=1.70, .0669" LH 1 $9.05
90564-50128 T=1.72, .0677" LH 1 $9.05
90564-50189 T=1.74, .0685" LH 1 $9.05
90564-50190 T=1.76, .0693" LH 1 $11.31
90564-50130 T=1.78, .0700" LH 1 $9.05
90564-50191 T=1.80, .0709" LH 1 $11.31
90564-50192 T=1.82, .0717" LH 1 $11.31
90564-50132 T=1.84, .0724" LH 1 $9.05
90564-50193 T=1.86, .0732" LH 1 $11.31
90564-50194 T=1.88, .0740" LH 1 $11.31
90564-50134 T=1.90, .0748" LH 1 $11.31
90564-50195 T=1.92, .0756" LH 1 $11.31
90564-50196 T=1.94, .0764" LH 1 $11.31
90564-50136 T=1.96, .0772" LH 1 $11.31
90564-50197 T=1.98, .0780" LH 1 $11.31
90564-50198 T=2.00, .0787" LH 1 $11.31
90564-50138 T=2.02, .0795" LH 1 $11.31
90564-50199 T=2.04, .0803" LH 1 $11.31
90564-50200 T=2.06, .0811" LH 1 $11.31
90564-50140 T=2.08, .0819" LH 1 $11.31
90564-50201 T=2.10, .0827" LH 1 $11.31
90564-50202 T=2.12, .0835" LH 1 $11.31
90564-50142 T=2.14, .0843" LH 1 $11.31
90564-50203 T=2.16, .0850" LH 1 $11.31
90564-50231 T=2.18, .0858" LH 1 $11.27
90564-50232 T=2.20, .0866" LH 1 $11.27
90564-50233 T=2.22, .0874" LH 1 $11.27
90564-50234 T=2.24, .0882" LH 1 $11.27
90564-50235 T=2.26, .0890" LH 1 $11.27
90564-50236 T=2.28, .0898" LH 1 $11.27
90564-50237 T=2.30, .0906" LH 1 $11.27
90564-50224 T=1.44, .0567" RH 1 $9.05
90564-50225 T=1.46, .0575" RH 1 $9.05
90564-50226 T=1.48, .0583" RH 1 $9.05
90564-50227 T=1.50, .0591" RH 1 $9.05
90564-50228 T=1.52, .0598" RH 1 $9.05
90564-50229 T=1.54, .0606" RH 1 $9.05
90564-50230 T=1.56, .0614" RH 1 $9.05
90564-50204 T=1.58, .0622" RH 1 $9.05
90564-50154 T=1.60, .0630" RH 1 $9.05
90564-50205 T=1.62, .0638" RH 1 $9.05
90564-50206 T=1.64, .0646" RH 1 $9.05
90564-50156 T=1.66, .0654" RH 1 $9.05
90564-50207 T=1.68, .0661" RH 1 $9.05
90564-50208 T=1.70, .0669" RH 1 $9.05
90564-50158 T=1.72, .0677" RH 1 $9.05
90564-50209 T=1.74, .0685" RH 1 $9.05
90564-50210 T=1.76, .0693" RH 1 $9.05
90564-50160 T=1.78, .0700" RH 1 $9.05
90564-50211 T=1.80, .0709" RH 1 $11.31
90564-50212 T=1.82, .0717" RH 1 $9.05
90564-50162 T=1.84, .0724" RH 1 $9.05
90564-50213 T=1.86, .0732" RH 1 $9.05
90564-50214 T=1.88, .0740" RH 1 $11.31
90564-50164 T=1.90, .0748" RH 1 $9.05
90564-50215 T=1.92, .0756" RH 1 $11.31
90564-50216 T=1.94, .0764" RH 1 $11.31
90564-50166 T=1.96, .0772" RH 1 $9.05
90564-50217 T=1.98, .0780" RH 1 $11.31
90564-50218 T=2.00, .0787" RH 1 $11.31
90564-50168 T=2.02, .0795" RH 1 $9.05
90564-50219 T=2.04, .0803" RH 1 $11.31
90564-50220 T=2.06, .0811" RH 1 $11.31
90564-50170 T=2.08, .0819" RH 1 $11.31
90564-50221 T=2.10, .0827" RH 1 $11.31
90564-50222 T=2.12, .0835" RH 1 $11.31
90564-50172 T=2.14, .0843" RH 1 $11.31
90564-50223 T=2.16, .0850" RH 1 $11.31
8" clamshell pinion seal----oem 90311-41009 MSRP $17.86
oem range to drive seal down below the surface is .165"~.189"
solid collar = 1.387" + .032" = 1.419"
PINION SHIM******PINION SHIM*******PINION SHIM
90564-35109 T=1.70 .0669" $3.52
90564-35110 T=1.73 .0681" $3.52
90564-35111 T=1.76 .0693" $3.52
90564-35112 T=1.79 .0705" $10.64
90564-35113 T=1.82 .0717" $3.52
90564-35114 T=1.85 .0728" $3.52
90564-35115 T=1.88 .0740" $3.52
90564-35116 T=1.91 .0752" $3.52
90564-35117 T=1.94 .0764" $3.52
90564-35118 T=1.97 .0776" $3.52
90564-35119 T=2.00 .0787" $3.52
90564-35120 T=2.03 .0799" $3.52
90564-35121 T=2.06 .0811" $3.52
90564-35123 T=2.09 .0823" $3.52
90564-35124 T=2.12 .0835" $3.52
90564-35125 T=2.15 .0846" $3.52
90564-35126 T=2.18 .0858" $3.52
90564-35127 T=2.21 .0870" $3.52
90564-35128 T=2.24 .0882" $3.52
90564-35129 T=2.27 .0894" $3.52
90564-35130 T=2.30 .0906" $3.52
90564-35131 T=2.33 .0917"
The above pinion shims fit the 8" clams also the standard low or high pinion 8" 3rds....both 4cyl and V6.
The very common 8" pinion shim sizes/part numbers....
90564-35109 T=1.70 .0669" $3.52
90564-35110 T=1.73 .0681" $3.52
90564-35111 T=1.76 .0693" $3.52
90564-35112 T=1.79 .0705" $10.64
90564-35113 T=1.82 .0717" $3.52
90564-35114 T=1.85 .0728" $3.52
90564-35115 T=1.88 .0740" $3.52
90564-35116 T=1.91 .0752" $3.52
90564-35117 T=1.94 .0764" $3.52
90564-35118 T=1.97 .0776" $3.52
90564-35119 T=2.00 .0787" $3.52
90564-35120 T=2.03 .0799" $3.52
90564-35121 T=2.06 .0811" $3.52
90564-35123 T=2.09 .0823" $3.52
90564-35124 T=2.12 .0835" $3.52
90564-35125 T=2.15 .0846" $3.52
90564-35126 T=2.18 .0858" $3.52
90564-35127 T=2.21 .0870" $3.52
90564-35128 T=2.24 .0882" $3.52
90564-35129 T=2.27 .0894" $3.52
90564-35130 T=2.30 .0906" $3.52
90564-35131 T=2.33 .0917"
2010-2017 fsm starts at page 1264
ring gear 12mm flange bolts (10) ------------ 85 ft/lb
Lid 10 bolts ----------------------------------37 ft/lb (2010~2017 models) that what it says.
steel tube(passenger side) --------------------- 81 ft/lb (2010~2017 models) E14 torx socket 4 bolts
****************Drill grommet hole 2.300" below lip....try 2.7~3.0 inches
***************better location....is 3" down from seal lip (in the cow pasture and not in the valley)
41015 Seal------( late model clams) recess the seal .110 ~ .130"
41009 Seal----- seal depth= .170" (.154~.184")
steel tubular arm seal (passenger side) BH5321F 90311-47013 or BH5321H 90311-47026 for the late model ones
use .222" of 4 cyl washer plates and a V6 8" race
driverside seal....use 47027 Use 32012 inner race to tap seal on flush
*********************************************************************************************************************************
8.2"
*********************************************************************************************************************************
4Runner/FJC 8.2" rear diff washer plates
2010 & Newer Toyota 4Runner with OEM rear E-locker
2010-2014 Toyota FJ Cruiser with OEM rear E-locker (All manual transmission models have OEM 3.90 ratio)
2009 & Newer Toyota Prado 150 Series with OEM rear E-locker
2009 & Newer Lexus GX460 without OEM rear E-locker
41334C WASHER, PLATE (FOR REAR DIFFERENTIAL SIDE GEAR SHAFT)
Part number mm inches Retail
90564-46052 T=2.06, .0811"
90564-46053 T=2.08, .0819"
90564-46054 T=2.10, .0827"
90564-46055 T=2.12, .0835"
90564-46056 T=2.14, .0843"
90564-46057 T=2.16, .0850"
90564-46058 T=2.18, .0858"
90564-46059 T=2.20, .0866"
90564-46060 T=2.22, .0874"
90564-46061 T=2.24, .0882"
90564-46062 T=2.26, .0890"
90564-46063 T=2.28, .0898"
90564-46064 T=2.30, .0901"
90564-46065 T=2.32, .0913"
90564-46066 T=2.34, .0921"
90564-46067 T=2.36, .0929"
90564-46068 T=2.38, .0937"
90564-46069 T=2.40, .0945"
90564-46044 T=2.42, .0953" $11.31
90564-46045 T=2.44, .0961" $11.31 overseas part and delayed 2 months
90564-46046 T=2.46, .0969" $11.31 overseas part and delayed 2 months
90564-46047 T=2.48, .0976" $11.31 overseas part and delayed 2 months
90564-46048 T=2.50, .0984" $11.31 overseas part and delayed 2 months
90564-46049 T=2.52, .0992" $11.31 overseas part and delayed 2 months
90564-46050 T=2.54, .1000" $11.31 overseas part and delayed 2 months
90564-46051 T=2.56, .1008" $11.31
90201-52001 T=2.58, .1016" $5.93
90564-46014 T=2.60, .1024" $15.58
90564-46015 T=2.62, .1031" $10.44
90201-52003 T=2.64, .1039" $5.93
90564-46016 T=2.66, .1047" $10.44
90564-46017 T=2.68, .1055" $10.44
90201-52005 T=2.70, .1063" $7.04
90564-46018 T=2.72, .1071" $12.41
90564-46019 T=2.74, .1079" $12.41
90201-52007 T=2.76, .1087" $7.04
8.2" Pinion WASHER, PLATE (FOR REAR DIFFERENTIAL DRIVE PINION)
90564-64062 T=1.85 .0728
90564-64064 T=1.87 .0736
90564-64066 T=1.89 .0744
90564-64068 T=1.91 .0752
90564-64070 T=1.93 .0760
90564-64072 T=1.95 .0768
90564-64074 T=1.97 .0776
90564-64076 T=1.99 .0783
90564-64078 T=2.01 .0791
90564-64080 T=2.03 .0799
90564-64082 T=2.05 .0807
90564-64084 T=2.07 .0815
90564-64086 T=2.09 .0823
90564-64088 T=2.11 .0831
90564-64090 T=2.13 .0839
90564-64092 T=2.15 .0846
90564-64094 T=2.17 .0854
90564-64096 T=2.19 .0862
90564-64098 T=2.21 .0870
90564-64100 T=2.23 .0878
90564-64102 T=2.25 .0886
90564-64104 T=2.27 .0894
90564-64106 T=2.29 .0902
90564-64108 T=2.31 .0909
ring bolts(12) 71 ft/lb Ring gear bolts(12 quantity) 11mm flange style 90105-11061
caps(4) 76/lb
pinion seal 90311-44008 XH0964E NOK recess 0 (use 32012 inner race to tap in flush)
pinion nut absolute max torque is 337 ft/lb
Pinion bearing inner ST4096
Carrier bearing OEM STA5083/5383 90366-50130 (use STB5083 with Eaton elockers) (90366-50001 is dimensionally same as 90366-50130)
diff carrier to axle housing (11) 38 ft/lb
drain and fill plugs--- 36 ft/lb
driveshaft bolts(4) ---- 65 ft/lb
ring bolts (12) 71 per fsm verified
caps(4) 76 per fsm verified
pinion seal 90311-44008 XH0964E NOK(flush verified)
pinion nut max = 337 ft/lb max
Big PB ST4096 90366-40132
small outer pinion bearing Koyo STA3574 90366-35157
CB(2) STB5083 / STA5383 (correct part number) 90366-50130 (90366-50001 is dimensionally same as 90366-50130)
seal depth = 0
lock indicator sw 30 ft/lb
diff carrier to axle housing (11) 38 ft/lb
drain and fill plugs--- 36 ft/lb
driveshaft bolts(4) ---- 65 ft/lb
32012 widget will tap the seal (90311-44008) in flush
*********************************************************************************************************************************
8.4"
*********************************************************************************************************************************
Toyota Tacoma 4x4 Rear (95.5-2015)
Toyota T100 (97-present)
Toyota Tundra (99-06)
Pinion bearing outer 90368-34007 8.4" Carrier bearing plates 8.4" pinion "shims"
Pinion bearing inner 90366-40068
Carrier bearing (2) 90366-51001
pinion seal 90311-44007 (NOK BH4053G) recess 0
ring (12) 92 ft/lb per fsm
brace cap (4) 83 per fsm
*********************************************************************************************************************************
8.75" Tacoma
*********************************************************************************************************************************
Tacoma 8.75 rear diff washer plates
2016 & Newer Toyota Tacoma, Automatic with OEM locker
2016 & Newer Toyota Tacoma, Manual with or without OEM locker
2016 & Newer Toyota Hilux Revo With or without OEM Locker
"LH" side is a bigger OD of 3.230" (elocker side)
"RH" side is smaller 2.951"
Part number mm inches Retail
90564-59044 T=2.08, .0819" LH 1
90564-59045 T=2.10, .0827" LH 1
90564-59046 T=2.12, .0835" LH 1
90564-59047 T=2.14, .0842" LH 1
90564-59048 T=2.16, .0850" LH 1
90564-59049 T=2.18, .0858" LH 1
90564-59050 T=2.20, .0866" LH 1
90564-59051 T=2.22, .0874" LH 1
90564-59052 T=2.24, .0882" LH 1
90564-59053 T=2.26, .0890" LH 1
90564-59054 T=2.28, .0898" LH 1
90564-59055 T=2.30, .0906" LH 1
90564-59056 T=2.32, .0913" LH 1
90564-59057 T=2.34, .0921" LH 1
90564-59058 T=2.36, .0929" LH 1
90564-59059 T=2.38, .0937" LH 1
90564-59060 T=2.40, .0945" LH 1
90564-59061 T=2.42, .0953" LH 1
90564-59062 T=2.44, .0961" LH 1
90564-59063 T=2.46, .0969" LH 1
90564-59064 T=2.48, .0976" LH 1
90564-59065 T=2.50, .0984" LH 1
90564-59066 T=2.52, .0992" LH 1
90564-59067 T=2.54, .1000" LH 1
90564-59068 T=2.56, .1008" LH 1
90564-59069 T=2.58, .1016" LH 1
90564-59070 T=2.60, .1024" LH 1
90564-59071 T=2.62, .1032" LH 1
90564-59072 T=2.64, .1039" LH 1
90564-59073 T=2.66, .1047" LH 1
90564-59074 T=2.68, .1055" LH 1
90564-59075 T=2.06, .0811" RH 1
90564-59076 T=2.08, .0819" RH 1
90564-59077 T=2.10, .0827" RH 1
90564-59078 T=2.12, .0835" RH 1
90564-59079 T=2.14, .0842" RH 1
90564-59080 T=2.16, .0850" RH 1
90564-59081 T=2.18, .0858" RH 1
90564-59082 T=2.20, .0866" RH 1
90564-59083 T=2.22, .0874" RH 1
90564-59084 T=2.24, .0882" RH 1
90564-59085 T=2.26, .0890" RH 1
90564-59086 T=2.28, .0898" RH 1
90564-59087 T=2.30, .0906" RH 1
90564-59088 T=2.32, .0913" RH 1
90564-59089 T=2.34, .0921" RH 1
90564-59090 T=2.36, .0929" RH 1
90564-59091 T=2.38, .0937" RH 1
90564-59092 T=2.40, .0945" RH 1
90564-59093 T=2.42, .0953" RH 1
90564-59094 T=2.44, .0961" RH 1
90564-59095 T=2.46, .0969" RH 1
90564-59096 T=2.48, .0976" RH 1
90564-59097 T=2.50, .0984" RH 1
90564-59098 T=2.52, .0992" RH 1
90564-59099 T=2.54, .1000" RH 1
90564-59100 T=2.56, .1008" RH 1
90564-59101 T=2.58, .1016" RH 1
90564-59102 T=2.60, .1024" RH 1
90564-59103 T=2.62, .1032" RH 1
90564-59104 T=2.64, .1039" RH 1
90564-59105 T=2.66, .1047" RH 1
90564-59106 T=2.68, .1055" RH 1
Pinion washer plates (behind the inner pinion race)
90564-78001 T=1.72, .0677" 1
90564-78002 T=1.74, .0685"
90564-78003 T=1.76, .0693"
90564-78004 T=1.78, .0701"
90564-78005 T=1.80, .0709" 1
90564-78006 T=1.82, .0717"
90564-78007 T=1.84, .0724" 1
90564-78008 T=1.86, .0732"
90564-78009 T=1.88, .0740" 1
90564-78010 T=1.90, .0748"
90564-78011 T=1.92, .0756" 1
90564-78012 T=1.94, .0764" 3
90564-78013 T=1.96, .0772" 4
90564-78014 T=1.98, .0780" 3
90564-78015 T=2.00, .0787" 2
90564-78016 T=2.02, .0795" 1
90564-78017 T=2.04, .0803" 2
90564-78018 T=2.06, .0811" last 3 coming...national backorder 10-26-21
90564-78019 T=2.08, .0819" last 1 coming...national backorder 10-26-21
90564-78020 T=2.10, .0827" 2coming no more this year
90564-78021 T=2.12, .0835"
90564-78022 T=2.14, .0843" 2coming
90564-78023 T=2.16, .0850"
90564-78024 T=2.18, .0858" 1coming
Carrier bearing BIG STB5083/STA5383 KOYO 90366-T0068
Carrier bearing SMALL STA5076/STA4076 KOYO 90366-T0071
Pinion bearing outer STN3580/ST3680 KOYO 90366-T0062
Pinion bearing inner TRD091004/same KOYO 90366-T0065
Pinion seal XH1691E NOK 90311-T0065 $18.93 verified
Blue connector 82824-0K060 $29.77 verified
Black connector(Lock Indicator) 84222-0K010 $90.10 verified
8.75" paper gasket 42181-KK010 $10.37
8.75" ring bolts(12) 92 per testing
8.75" caps(4) 84 per testing
For the 3rd gen Tacos without the rear elocker (the open 8" rear instead)............
90366-T0080 = (IPB) TR070904-3/TR080904-1 (the usual V6 inner pinion bearing!)
90366-T0083 = (OPB) STA3072-2/STA3072 (the usual V6 outer pinion bearing!)
90366-T0010 = (carrier bearings) ST5383/ST5383 53mm journals
90311-T0068 = 3rd gen pinion seal for 8" V6 model
When replacing open 2 pinion center carrier(53mm journals on the 3rd gen TRD Sports) with Harrop/Eaton 14211-1(50mm journals)....then use this carrier bearing....
(90366-50007) 50/83mm ...same bearing used in the 8" V6 carrier bearing TR100802
No issues with Deck height and ring gear bolts business as usual. 9-12-19
*********************************************************************************************************************************
9.5" pinion shims and washer plates
*********************************************************************************************************************************
FJ60,62,80 Landcruisers 1980-1997
9.5" pinion shims below
Part Number inches mm
90564-40004 .0413 T=1.050
90564-40009 .0423 T=1.075
90564-40007 .0435 T=1.100
90564-40008 .0443 T=1.125
90564-40009 .0453 T=1.150
90564-40010 .0463 T=1.175
90564-40011 .0472 T=1.200
90564-40012 .0482 T=1.225
90564-40013 .0492 T=1.250
90564-40014 .0502 T=1.275
90564-40015 .0512 T=1.300
90564-40016 .0522 T=1.325
90564-40017 .0532 T=1.350
90564-40018 .0541 T=1.375
90564-40019 .0551 T=1.400
90564-40020 .0561 T=1.425
90564-40021 .0571 T=1.450
90564-40022 .0581 T=1.475
90564-40023 .0591 T=1.500
90564-40024 .0600 T=1.525
90564-40025 .0610 T=1.550
FJ80 9.5" E-Locker carrier bearing washer plates
mm inches Part number
2.67 .1051 90201-79001
2.70 .1063 90201-79002
2.73 .1075 90201-79003
2.76 .1087 90201-79004
2.79 .1098 90201-79005
2.82 .1110 90201-79006
2.85 .1122 90201-79007
2.88 .1134 90201-79008
2.91 .1146 90201-79009
2.94 .1157 90201-79010
2.97 .1169 90201-79011
3.00 .1181 90201-79012
3.03 .1193 90201-79013
3.06 .1205 90201-79014
3.09 .1217 90201-79015
3.12 .1228 90201-79016
3.15 .1240 90201-79017
3.18 .1252 90201-79018
3.21 .1264 90201-79019
3.24 .1276 90201-79020
3.27 .1287 90201-79021
3.30 .1299 90201-79022
3.33 .1311 90201-79023
ring 10 bolts 81 ft/lb
caps for the elocker 83 ft/lb
oem rubberized pinion seal NOK AH2261K 27 spl
seal recessed 1mm
38047 seal is ok.
*********************************************************************************************************************************
10.5" Tundra
*********************************************************************************************************************************
10.5" Tundra rear 3rd washer plates
90564-A0044 T=1.66, .0654 MARK 66 2 $4.67
90564-A0045 T=1.68, .0661 MARK 68 2 $8.26
90564-A0046 T=1.70, .0669 MARK 70 2 $8.26
90564-A0047 T=1.72, .0677 MARK 72 2 $8.26
90564-A0048 T=1.74, .0685 MARK 74 2 $8.26
90564-A0049 T=1.76, .0693 MARK 76 2 $8.26
90564-A0050 T=1.78, .0700 MARK 78 2 $8.26
90564-A0051 T=1.80, .0709 MARK 80 2 $8.26
90564-A0052 T=1.82, .0717 MARK 82 2 $8.26
90564-A0053 T=1.84, .0724 MARK 84 2 $8.26
90564-A0054 T=1.86, .0732 MARK 86 2 $8.26
90564-A0055 T=1.88, .0740 MARK 88 2 $8.26
90564-A0056 T=1.90, .0748 MARK 90 2 $8.26
90564-A0057 T=1.92, .0756 MARK 92 2 $8.26
90564-A0058 T=1.94, .0764 MARK 94 2 $8.26
90564-A0059 T=1.96, .0772 MARK 96 2 $8.26
90564-A0060 T=1.98, .0780 MARK 98 2 $8.26
90564-A0061 T=2.00, .0787 MARK 00 2 $8.26
90564-A0062 T=2.02, .0795 MARK 02 2 $8.26
90564-A0063 T=2.04, .0803 MARK 04 2 $8.26
90564-A0064 T=2.06, .0811 MARK 06 2 $8.26
90564-A0065 T=2.08, .0819 MARK 08 2 $8.26
90564-A0066 T=2.10, .0827 MARK 10 2 $8.26
90564-A0067 T=2.12, .0835 MARK 12 2 $8.26
90564-A0068 T=2.14, .0843 MARK 14 2 $8.26
90564-A0069 T=2.16, .0850 MARK 16 2 $8.26
90564-A0070 T=2.18, .0858 MARK 18 2 $8.26
90564-A0071 T=2.20, .0866 MARK 20 2 $8.26
90564-A0072 T=2.22, .0874 MARK 22 2 $8.26
90564-A0073 T=2.24, .0882 MARK 24 2 $8.26
90564-A0074 T=2.26, .0890 MARK 26 2 $8.26
90564-A0075 T=2.28, .0898 MARK 28 2 $8.26
90564-A0076 T=2.30, .0906 MARK 30 2 $8.26
90564-A0077 T=2.32, .0913 MARK 32 2 $8.26
90564-A0078 T=2.34, .0921 MARK 34 2 $8.26
90564-A0079 T=2.36, .0929 MARK 36 2 $8.26
90564-A0080 T=2.38, .0937 MARK 38 2 $8.26
90564-A0081 T=2.40, .0945 MARK 40 2 $8.26
90564-A0082 T=2.42, .0953 MARK 42 2 $8.26
90564-A0083 T=2.44, .0961 MARK 44 2 $8.26
90564-A0084 T=2.46, .0969 MARK 46 2 $8.26
10.5" Tundra solid collar "shims" (2 required)
90564-A0022 T=1.90 .0748 1 $2.17
90564-A0023 T=2.00 .0787 1 $2.17
90564-A0024 T=2.10 .0827 1 $2.17
90564-A0025 T=2.20 .0866 1 $3.12
90564-A0026 T=2.30 .0906 1 $3.12
90564-A0027 T=2.40 .0945 1 $3.12
90564-A0028 T=2.50 .0984 1 $3.12
90564-A0029 T=2.60 .1024 1 $3.12
90564-A0030 T=2.70 .1063 1 $3.12
90564-A0031 T=2.80 .1102 1 $3.12
90564-A0032 T=2.90 .1142 1 $3.12
90564-A0033 T=3.00 .1181 1 $3.12
90564-A0034 T=1.80 .0709 1 $2.17
90564-A0035 T=1.81 .0713 1 $2.17
90564-A0036 T=1.82 .0717 1 $2.17
90564-A0037 T=1.83 .0720 1 $2.17
90564-A0038 T=1.84 .0724 1 $2.17
90564-A0039 T=1.85 .0728 1 $2.17
90564-A0040 T=1.86 .0732 1 $2.17
90564-A0041 T=1.87 .0736 1 $2.17
90564-A0042 T=1.88 .0740 1 $2.17
90564-A0043 T=1.89 .0744 1 $2.17
10.5" Pinion Head depth shims........(fits on 8.75" pinion also)
90564-A0001 .0394 T=1.000
90564-A0002 .0404 T=1.025
90564-A0003 .0413 T=1.050
90564-A0004 .0423 T=1.075
90564-A0005 .0433 T=1.100
90564-A0006 .0443 T=1.125
90564-A0007 .0453 T=1.150
90564-A0008 .0463 T=1.175
90564-A0009 .0472 T=1.200
90564-A0010 .0482 T=1.225
90564-A0011 .0492 T=1.250
90564-A0012 .0502 T=1.275
90564-A0013 .0512 T=1.300
90564-A0014 .0522 T=1.325
90564-A0015 .0531 T=1.350
90564-A0016 .0541 T=1.375
90564-A0017 .0551 T=1.400
90564-A0018 .0561 T=1.425
90564-A0019 .0571 T=1.450
90564-A0020 .0581 T=1.475
90564-A0021 .0591 T=1.500
specs ring(12) 145 per fsm
caps(4) 151 per fsm
PPL= 16~28 new per fsm start
PPL= 15~19 used per fsm start
CBPL= 3 per fsm
pinion seal depth = 0 per fsm
drain and fill plugs 36 ft/lb
diff nuts(10) 53
driveshaft nuts(4) 52
pinion nut 224 max
4.10 factory non-towing package
4.30 with towing package
Carrier Bearings ---- koyo STC4085 / STC4085 (90366-A0020)
big Pinion Bearing----- koyo TRA091104 / TRA091104 (90366-A0017)
small outer Pinion Bearing----- NSK HR 32011XJa4 / R55-34 (90366-A0023)
pinion seal---oem---90311-A0008 (NOK XH2152E)
diff gasket 42181-36060
Solid collars right from the factory.
*********************************************************************************************************************************
9"CLAM aluminum
*********************************************************************************************************************************
9" front clam washer plates
90564-50238 T=1.50 .0591 $9.49
90564-50239 T=1.52 .0598 $9.49
90564-50240 T=1.54 .0606 $11.82
90564-50241 T=1.56 .0614 $11.82
90564-50242 T=1.58 .0622 $11.82
90564-50243 T=1.60 .0630 $11.82
90564-50244 T=1.62 .0638 $11.82
90564-50245 T=1.64 .0646 $11.82
90564-50246 T=1.66 .0654 $11.82
90564-50247 T=1.68 .0661 $11.82
90564-50248 T=1.70 .0669 $11.82
90564-50249 T=1.72 .0677 $14.19
90564-50250 T=1.74 .0685 $14.19
90564-50251 T=1.76 .0693 $11.82
90564-50252 T=1.78 .0700 $11.82
90564-50253 T=1.80 .0709 $11.82
90564-50254 T=1.82 .0717 $11.82
90564-50255 T=1.84 .0724 $11.82
90564-50256 T=1.86 .0732 $11.82
90564-50257 T=1.88 .0740 $11.82
90564-50258 T=1.90 .0748 $11.82
90564-50259 T=1.92 .0756 $11.82
90564-50260 T=1.94 .0764 $11.82
90564-50261 T=1.96 .0772 $11.82
90564-50262 T=1.98 .0780 $11.82
90564-50263 T=2.00 .0787 $11.82
90564-50264 T=2.02 .0795 $11.82
90564-50265 T=2.04 .0803 $11.82
90564-50266 T=2.06 .0811 $11.82
90564-50267 T=2.08 .0819 $11.82
90564-50268 T=2.10 .0827 $11.82
90564-50269 T=2.12 .0835 $11.82
90564-50270 T=2.14 .0843 $11.82
90564-50271 T=2.16 .0850 $11.82
90564-50272 T=2.18 .0858 $11.82
90564-50273 T=2.20 .0866 $14.19
90564-50274 T=2.22 .0874 $14.19
90564-50275 T=2.24 .0882 $14.19
90564-50276 T=2.26 .0890 $14.19
90564-50277 T=2.28 .0898 $14.19
90564-50278 T=2.30 .0906 $14.19
90564-50279 T=2.32 .0914 $14.19
90564-50280 T=2.34 .0921 $14.19
pinion washer plate (behind big inner race)
90564-63065 T=1.825 .0719
90564-63066 T=1.850 .0728
90564-63067 T=1.875 .0738
90564-63068 T=1.900 .0748
90564-63069 T=1.925 .0758
90564-63070 T=1.950 .0768
90564-63071 T=1.975 .0778
90564-63072 T=2.000 .0787
90564-63074 T=2.025 .0797
90564-63075 T=2.050 .0807
90564-63076 T=2.075 .0817
90564-63077 T=2.100 .0827
90564-63078 T=2.125 .0837
90564-63079 T=2.150 .0846
90564-63080 T=2.175 .0856
90564-63081 T=2.200 .0866
90564-63082 T=2.225 .0876
90564-63083 T=2.250 .0886
90564-63084 T=2.275 .0896
pinion seal 90311-46006(up to 05/2015)
90311-46007(from 05/2015)
Seal RH 90311-47026
Seal LH 90311-47027(replaces 47011 47012 47020 T0015)
snap ring(RH stub shaft) 90521-37010
carrier bearing(2) 90366-58013
63.8 pounds bare....no mounts no arm
ring bolts (12) 101 per fsm
Case (11) 48 per fsm verified
fill plug 29 ft/lb
drain plug 29
tube assembly(4 bolts 17mm) 48 ft/lb per pdf
pinion nut 333 ft/lb max
seal depth .221~.259" verified (.250/.235 measured)
PPL 27~30 verified
confusion on FSM...15~21 and 27~30 preloads mentioned. (new)
outer PB EM6733 (90363-35063)
inner PB Nachi 40KD903 SLT CLK (90366-40114)
CB (2) Koyo ST5889 (90366-58013)
RH seal (end of tube) 90311-47026
LH seal (small one) 90311-47027
pinion seal 90311-46007 (May of 2015---> models) NOK XH0533G
pinion seal 90311-46006 (<---May of 2015 models) NOK XH0533E
*********************************************************************************************************************************
*********************************************************************************************************************************
Supra LSD info
Supra LSD install (into standard V6 carrier)......... carrier bearing requirements
ring bolt side bearing(Supra carrier bearing) = Toyota part # 90366-50001 $49.93 retail (Nachi 50KB8301 cone and cup) (50mm ID x 83mm OD) (90366-50001 is dimensionally same as 90366-50130)
ring tooth side bearing = V6 truck bearing (90366-50007)
conversion bearings (90368-50024) allow SUPRA LSD to fit in a 4 cyl 3rd....verified. See next line.
4 cyl 3rd----use two 90368-50024 and one washer plate (90201-65023).
for a 1986 Supra(MA70L-BJMZA)
90311-38010 pinion seal
90311-43001 (x2) side gear shaft seal replaced by 90311-43009
90366-30025 outer pinion bearing
90366-35028 inner pinion bearing
41204-35040 companion flange (27 spline normally)
*********************************************************************************************************************************
*********************************************************************************************************************************
HOME